If you connect Alfabox UX3 and the screen is “jumping” or there is a black screen and you see one of the messages on the screen: no signal mode not supported missed matched output That means the resolution is not supported. The resolution has to be changed from BIOS (Basic Input/Output System). Follow the steps […]
Category: 3. ALFABOX
How to fix program guide if it doesn’t show list of programs/ Wrong date on the screen
Program Guide uses time set on the box. The Box gets time from the time server that is set in settings. If there is no program guide available then NTP server is not set properly. Follow the instructions below to set up the NTP server: Click SET to go to System Settings screen. Select Servers and […]
Alfabox supports the following WiFi adapters
Model Chipset Notes Alfabox1 Alfabox2 Alfabox3 ASUS USBN13 Ralink RT3071 + + ASUS USBN13 rev.B1 Realtek RTL8192CU – – ASUS USBN14 Realtek RTL8192CU 0.2.18r12 + + Asus USBN53 Ralink RT3572 0.2.18r12 + + Asus USBN53 rev.B1 MediaTek MT7612U – – DLink DWA125 rev.A1, A2, A3 Ralink RT3070 Ralink RT5370 H/W Ver.: A1, A2 (A3 – after […]
How to program Alfabox remote control to work with any TV
Alfabox remote control can be programmed to control any TV in just a few steps. Buttons that can be programmed are highlighted by a solid white line at the top of the remote. New remote control To program the buttons do the following: Press the «On/Off» and «A/V» buttons at the same time and hold it for 2 […]
How to fix endless restarting of the box with the message “Alfabox”
Please disconnect the LAN (internet) cable from the box. After that, you will see a window with the message on the top – “Page loading error”. (If you won’t see this message then use this link to fix the issue). Press the “Ok” button on the “System settings”. Choose the icon “Video” and press “Ok”. Select “Video output mode” and […]
How to reload portal
If you need restart Alfabox (reload portal) please follow the instruction: Find and press the “Setup” (gear) button on the remote control. Select “Restart Portal” section and press two times “OK” button. Select your service icon again and press OK. Service will load with new settings applied.
Alfabox UX1 specification
Alfabox advantages: High quality of sound and image (supports all modern video and audio formats, including full HD) Compatible with any TV (HDMI and RCA television compatible) Flawless Design (lightweight, elegant design that will fit in with any interior) Maximum Comfort (remote control enables you to control not only set-top-box but also the other devices) […]
Alfabox UX3 specification
Alfabox advantages: High quality of sound and image (supports all modern video and audio formats, including full HD) Compatible with any TV (HDMI and RCA television compatible) Flawless Design (lightweight, elegant design that will fit in with any interior) Maximum Comfort (remote control enables you to control not only set-top-box but also the other devices) […]
How to update firmware on Alfabox UX3 (message on the screen TV, Videoteka, Settings)
Below you can find a detailed process of firmware updating to new stable version: Go to box settings/software update Press “OK” on the remote to verify and get pop-up information page Press “F1” on the remote to update It will be restarted automatically when it’s done Important! Do NOT restart/turn-off the box while it’s updating.
Alfabox UX3: Reset to default settings, boot mode change
Press and hold service button (FN) on the back side of STB until STB is power off, or during 2 seconds after power on. Switching between modes done by releasing button at the specific time according to the LED indication. There are 4 modes: STB load from first U-boot; Switch to alternative NAND; Reset to […]